+86-551-68661901
홈 / 소식 / 내용

Jul 08, 2021

서미스터에 대한 약간의 질문

Designing a thermistor temperature sensing device can be challenging if you plan to use it over its entire temperature range. A thermistor is typically a high-impedance, resistive device, so it can simplify one of the interface issues when you need to convert the thermistor's resistance to a voltage value. A more challenging interface issue, however, is how to capture the thermistor's nonlinear behavior digitally with a linear ADC.

The term "thermistor" comes from a generalization of the description "heat{{0}}sensitive resistor". Thermistors include two basic types, positive temperature coefficient thermistors and negative temperature coefficient thermistors. Negative temperature coefficient thermistors are ideal for high-precision temperature measurement. To determine the temperature around the thermistor, you can do it with the help of the Steinhart-Hart formula: T=1/(A0 plus A1(lnRT) plus A3(lnRT3)). Among them, T is the temperature in Kelvin; RT is the resistance value of the thermistor at temperature T; and A0, A1 and A3 are constants provided by the thermistor manufacturer.

서미스터의 저항은 온도에 따라 변하며, 이 변화는{0}Steinhart{1}}Hart 공식에서 알 수 있듯이 비선형입니다. 온도 측정을 할 때 비선형 응답을 갖는 등가 전압을 생성하기 위해 기준 전류가 서미스터를 통해 구동되어야 합니다.{2}} 마이크로컨트롤러에 제공된 참조 표를 사용하여{3}서미스터의 비선형 응답을 보정할 수 있습니다. 마이크로컨트롤러 펌웨어에서 이러한 알고리즘을 실행할 수 있다 하더라도 극한의 온도에서 데이터 캡처를 위한 고정밀 변환기가 여전히 필요합니다.

Alternatively, you can use a "hardware linearization" technique and a lower precision ADC before digitizing. (Figure 1) One technique is to place a resistor RSER in series with the thermistor RTHERM and a reference voltage or power supply (see Figure 1). The PGA (Programmable Gain Amplifier) is set to 1V/V, but in such a circuit, a 10-bit precision ADC can only sense a very limited temperature range (about ±25 degree ).


그림 1에서 고온 영역은 그림 1에서 해결되지 않습니다. 그러나 이러한 온도 값에서 PGA의 이득이 증가하면 PGA의 출력 신호는 ADC가 안정적으로 제공할 수 있는 범위 내에서 제어할 수 있습니다. 서미스터의 온도를 식별하는 변환.

마이크로컨트롤러 펌웨어의 온도 감지 알고리즘은 10비트 정밀 ADC 디지털 값을 읽고 이를 PGA 히스테리시스 소프트웨어 루틴으로 전송합니다. PGA 히스테리시스 루틴은 PGA 이득 설정을 확인하고 ADC 디지털 값을 그림 1에 표시된 전압 노드 값과 비교합니다. ADC 출력이 전압 노드 값을 초과하면 마이크로컨트롤러는 PGA 이득을 다음으로 높은 값으로 설정합니다. 또는 더 낮은 게인 설정. 필요한 경우 마이크로 컨트롤러는 새 ADC 값을 다시 얻습니다. 그런 다음 PGA 이득 및 ADC 값은 마이크로컨트롤러 조각별 선형 보간 루틴으로 전달됩니다.

Getting data from a nonlinear thermistor is sometimes seen as an "impossible task". You can use a series resistor, a microcontroller, a 10-bit ADC, and a PGA to solve the measurement problems of non-linear thermistors beyond ±25 degree .


문자 보내